The RF6504 Transmit/Receive Front End Module features 1 dB interface Rx insertion loss, a separate 50? Tx/Rx Transceiver, and 30 dBm Tx output power. Two separate ports can be found on the device (Rx and Tx) The Rx port is a pass through port, and the Tx section provides a PA with nominal output power of 30dBm and 15dB gain. Both combine to one antenna port with a SP2T switch.
The RF6514 transmit/receive module features 30 dBm TX output power, 1 dB of RX insertion loss, and a separate 50W Tx/Rx transceiver interface. The module is intended for 470MHz to 510 MHz AMR solutions.
RFMD's RF3928B is a 380W GaN Wideband Pulsed Power Amplifier featuring a wideband operation of 2.8 GHz to 3.4 GHz, advanced heat-sink and GaN HEMT technology, integrated matching components for high terminal impedances, an optimized evaluation board layout for 50Ω operation, and more.
These high power front end modules are 6 x 6mm and have been designed for use in WiFi IEEE802.11b/g/n applications, access points/gateways, WiFi-enabled set-top boxes, customer premises equipment (CPE), data cards and terminals, and spread-spectrum and MMDS systems.
Skyworks' SMP1325-087LF is a surface mount PIN diode that can be used in an attenuator circuit, or an RF switch. It features a low total capacitance of 0.6 pF maximum @ 20 V, excellent thermal resistance of 40° C/W typical, low series resistance of 0.55 Ω maximum @ 100 mA, and more. A 2 W dissipation power rating allows this PIN diode to handle up to 50 W continuous wave (CW) and 500 W peak (1 µs pulse, 1 percent duty cycle) in a shunt-connected transmit/receive (T/R) switch.
RFMD's RFFM3482E is a single-band front end module (FEM) ideal for applications involving IEEE802.11b/g/n WiFi, 2.5GHz ISM Bands, portable battery-powered equipment, WiFi systems, and more. Its size is ideal for a 802.11b/g/n front end design and greatly reduces the number of components outside of the core chipset. This FEM has the ability to switch between WiFi Rx, WiFi Tx, and BTH Rx/Tx operations. An Rx balun, a b/g/n power amplifier, and a directional power detector have all been integrated into the RFFM3482E.
This solid state amplifier by AR has been designed for applications in which instantaneous bandwidth and high gain are required, such as RF susceptibility testing, antenna and component testing, watt meter calibration, particle accelerators, plasma generation, communications and use as a driver for higher power amplifiers. It is a self-contained, air-cooled, broadband, completely solid state amplifier with push-pull LDMOS circuitry utilized in all high power stages in the interest of lowering distortion and improving stability. A minimum of 600 watts of swept power can be provided when the 600A225 is used with an RF sweep generator.
RFMD's RF1293 is a switch filter module ideal applications involving cellular handsets, cellular modems and USB devices, multi-mode GSM, EDGE, WCDMA, and LTE. It offers very low insertion loss combined with excellent linearity performance. This particular switch filter module features excellent insertion loss and isolation performance, a very low current consumption, five linear paths offering band combination and air interface flexibility, full spec compliance down to a 1.3V control voltage, and more. With a 3.2mm x 3.5mm, 21-pin, module package, the RF1293 switch filter module offers a small sized solution with no need for external DC blocking capacitors when no external DC is applied to the device ports.
RFMD has several products that offer solutions for ZigBee applications in home sensors, home entertainment, commercial building monitoring, smart energy AMI, industrial device control, mobile service, and more. Below you'll find a list of some of RFMD's offerings as they relatesto ZigBee related applications.
Matched ports which reduce pulling in low noise amplifiers and deliver better system performance make this family of high power 50 Ohm terminated, single-pole, double throw switches ideal for high power access points and router applications. These SPDT switches feature low insertion loss, high isolation and high linearity for improved data throughput.
RFMD's RF1604D is a single-pole four throw (SP4T) switch that is ideal for applications involving receive diversity switching. It can also be used in multi-mode GSM/EDGE/WCDMA, LTE, and cellular infrastructure applications. This SP4T switch featured a low insertion loss of 0.4dB at 1GHz, a very high isolation of 40dB at 1GHz, compatibility with low voltage logic (VHIGH Min = 1.3V), the ability to operate at low frequencies to 2.7GHz, and more. The RF1604D SP4T switch includes integrated decoding logic, allowing just two control lines needed for switch control, and has been packaged in a 2.5mm x 2.5mm x 0.6mm, 12-pin, leadless QFN package, giving it a very compact form factor. This switch is most ideal for battery operated applications requiring high performance switching with very low DC power consumption.
RFMD's RF6599 915MHz Transmit/Receive Module features a Tx output power of 26dBm, a Tx gain of 14dB, an Rx insertion loss of 1dB, and an antenna diversity switch. This transmit/receive module is ideal for applications involving wireless automated metering, wireless alarm systems, portable battery powered equipment, and smart energy.
RFMD's RF6555 is a Front End Module (FEM) with a TX Output Power of 18 dBm, and a TX Gain of 25dB. It's ideal for WLAN and ZigBee® applications in the 2.4GHz to 2.5GHz band. In addition to its internal integrated LNA bypass mode, this FEM also integrates the PA plus harmonic filter in the transmit path. The RF6555 Front End Module provides a single balanced TDD access for RX and TX paths along with two ports on the output for connecting a diversity solution or a test port.
Trans-Tech Inc., a subsidiary of Skyworks Solutions, presents their TTZ-500 and TTZ-100 Hexagonal Ferrites ideal for Antenna, absorber and inductor applications for military and commercial markets. The TTZ-500 Hexagonal Ferrite was designed for 500 MHz antenna applications, and features the highest frequency resonance on any Z-phase material in the market. The TTZ-100 has been designed for 100 MHz antenna applications. Both chemical compounds may be supplied in powder form with custom particle sizes or as a sintered ceramic product with dimensions up to 4" x 4" squares.
Trans-Tech Inc, a subsidiary of Skyworks Solutions, presents 12 and 20 mm High Power Ceramic Filters ideal for applications involving electronic warfare, power amplifiers, and Portable transceivers for military/homeland security radio communications. These high power ceramic filters feature low insertion loss, a light weight, a wide operating temperature range, and more. They can be surface mount or connectorized, are RoHs compliant, are reconfigurable for many different connector types, and operate in a frequency range from UHF to 2.0 GHz.
